5ft mini ramp plans full#
5ft mini ramp plans plus#

There are already quite a few DIY project logs, build guides, instructables out there - though none seem to be completely detailed. Each of them is reasonably comfortable hitting smaller flatbanks, and my 9 year old is already trying to drop-in and hit small (3 foot) hips. In the day and age of video games (I work in IT, so it comes to them naturally), rather than immediately throwing them to the wolves and risking injury or boredom at our local skatepark due to our local skatepark's design (TONS of landscaping rocks everywhere, a terrible flow to the park, and a bad location) - I'd much rather help boost their progression by building a mini ramp in our backyard. My kids (3 boys ranging 3-12years) are starting to show a ton of interest in shredding.

5ft mini ramp plans full#

I work from home, am self-employed, and am (for now) a full time student, so naturally - my time is in very short supply. If you're looking for spots or people to skate with in your area ( click here to browse through posts tagged looking for spots/skaters) Use the discussion thread or /r/kookboarder if you must share prohibited content listed above. Flair descriptions can be found in the link above.If you don't provide source or skater's name Submit any and all questions to the discussion thread discussion threadģ.No snowboarding, snow skating, trampoline skating, ripstick, scooter, longboarding, etc. Your post must contain videos and/or pictures of skateboarding Otherwise, we won’t achieve the perfect half pipe build we want.Discord for r/Skateboarding here Submission Rules: 1. You now have the three major parts of the homemade mini ramp: the two transitions and the flat bottom.īefore fixing these three structures together, ensure the leveling of the ground. Subsequently, you’ll have a flat bottom with dimensions of 8ft x 7.75ft for your halfpipe. Press the two long sides of the wooden frames against each other and use screws to attach them.Finish installing all the 22 45-inch lumber pieces you prepared.Line the lumber up to both sides of the wooden frame and drill its ends. And like the framing we installed, the narrow side of the 2×4 lumber should be flush against the box for the flat bottom. Grab three screws and drill along the first 8-inch-interval mark on the frame.Each box for the flat bottom will use 11 of them.

Next, prepare 22 pieces of 2×4 lumber cut to 45” long.Put tick marks at 8-inch intervals on the longer sides of the boxes.Keep the narrow sides facing up to level with the lowest part of the transition. Using 2×4 lumber, frame up two wooden boxes that are 4ft x 7.75ft each. The flat bottom connects the two transitions.Repeat this step with the other transition. Otherwise, the curve may not be as smooth as we originally planned. Make sure you drill with the board’s narrow side against the transition.Begin from the lowest part of the ramp until you finish at the top or deck of the halfpipe. Finally, drill the 12 remaining lumber studs on the transition part of the halfpipe.Next, drill another stud on the other bottom corner of the ramp or at the right angle facing the curve.Keep the lumber and curve leveled to ensure the ramp is connected at the right points. Drill one stud on the lowest part of the transition, using three 1.5” screws at each end for firmness.Position them mirroring each other and with a distance the same as the lumber’s length. Cut 1/8” off the lumber to square the entire ramp. Double this number to support all four halfpipe walls.

5ft mini ramp plans plus#

Prepare 12 2×4 lumber pieces (8 ft in length) plus two more for the base. Suppose we ended up with 12 tick marks on the transition.These marks should have 8-inch intervals. Begin by putting tick marks on the transition part of the plywood you cut.But for this tutorial, we’ll go for the 3ft 5 in. Others might also serve you 6ft half pipe plans. Try to browse several sites for mini ramp plans, and most of them will give you 4ft. So, as a finishing touch, we can prepare exterior paint to protect these structures.īesides the paint, let’s not miss out on the steel coping to complete the ramp. More often than not, halfpipes sit in the yard unroofed. You may also want to prepare a rope to outline the transition and a level to ensure both ends are aligned. And for this purpose, a pencil will be necessary to draw lines and marks. We will do a lot of measuring tasks in this tutorial. While primary home tools can drive screws once you build a mini ramp, such options may not be efficient.